Supreme Landscaping Products Jointing Compound Stone Grey Easy Joint 12.5 Kilo Patio Mortar

Product Information

In terms of application, there is not so much need to use copious quantities of waterwith porcelain as the EASYJoint will not cause it to mark in the same way it can with stone or concrete. It is easier to use EASY Joint with two people, one of them to sweep the compound and the other one to spray the water.

The result of using EASYJoint, to joint your paving, will be a paving gap that is completely filled without the need for kneeling and compressing the material by hand that will last for years. EASYJoint in Stone Grey is the original sweep-in jointing Compound and still the best truly “All Weather Paving Joint Compound” available and made in the UK.

Secondly, the water helps the compound flow in to the joint cavities and helps with compaction for a fuller joint without voids. It will also allow any efflorescence or natural salts present in the sub-base and substrate to pass through the paving material and wear off naturally over time. Our tile adhesives and grouts are heat, mould and water resistant and perfect for fitting tiles in your bathroom or kitchen.

Always use a fan type nozzle at a 45 degree angle and no closer than 15 cms / 6 inches to avoid removing the jointing material from between your slabs. Use more EASY Joint to top up any low spots in your joints, repeating the washing process as described previously. It’s super simple to use, it’s fast, effective and fills joints in all types of paving slabs and flagstones with ease. When using the wet method - the water is used to assist our jointing compound into the joints, it will self-compact and fill any voids. The problem is that if you try to top up a joint it will not bond properly with the existing joint and over time the joint will fail.It is suitable for all types of paving material provided there is a gap of at least 3mm wide and 20mm deep. Water can also help the compound flow in to the full depth of the joint cavity and aids compression of the compound.

Freezing weather will increase the set time and will cause the process to virtually stop, it can take many days for the joints to set fully hard. Aquacut Aquacut Limited has a dedicated team of craftsmen with decades of experience processing a wide range of building materials such as porcelain, stone, metals, glass, and composites to create functional and beautiful building finishes. With no need to mix, this compound is quick to brush in and perfect to use alongside various forms of paving material. Whilst not essential, it is strongly recommended to "point" or "strike" the surface of the joints with a suitable finishing tool. By using lots of water when brushing the product in, it will ensure that any linseed oil will sit on top and simply get washed away!It is important to note that linseed oil staining is only a temporary stain and exposure to sunlight, will over time, lift the marks and fade away. EASYJoint Original is available in four different colours; Mushroom, Buff Sand, Stone Grey and Basalt, you can point your paving to suit the look you love. Ensure that no grains of sand are left on the surface, or the rainbow effect caused by the linseed oil. The end results will be a perfect joint that is fully filled without need for kneeling and compressing the material by hand that will last for years and years.

Due to the structural requirements of a driveway and that generally, the bedding mix is stronger than that of a patio or path, the use of EASY Joint is not recommended. Start once the paving has dried and the joints are drained, applying virtually no pressure to the tool - it is only to finish the joint, not compress it.

Because accuracy of gap width and depth cannot be uniformly guaranteed, the above table is only a reasonable estimate of the amount of material required. Utilise the same method when working with porcelain paving tiles as with working with stone or concrete. Peppard Building Supplies — North Reading’s Premier independent builders merchant and first choice for the professional and DIY enthusiast alike. Do not be tempted to use brick acid on paving, it will damage the paving and possibly the paving joint. When the water has drained away, a “flicking” motion with aclean soft hand brush (not the same one used to apply the compound) will aid the removal of any loose grains.